Overview

Runs Reticulum over HF radio using FreeDV data modes. Provides encrypted peer-to-peer communication without internet infrastructure.

Key Features:

• Web-based setup wizard - no command line required
• Live RX audio level from modem
• Instant mode and volume changes (no service restart)
• FreeDV mode selection based on band conditions
• VOX mode support for audio-only interfaces
• Works with Sideband, MeshChat, NomadNet

Tested Radios:

• Xiegu G90 (Digirig Mobile)
• Yaesu FT-818 (Digirig Mobile)
• (tr)uSDX (Digirig Lite + VOX)

Pre-built Image

Download the SD card image, flash it, boot, configure via web portal.

Download

reticulumhf-v0.3.0-alpha.img.xz

Quick Start

1. Flash to SD card using Raspberry Pi Imager
2. Insert SD card, connect radio via Digirig, power on
3. Connect to WiFi: ReticulumHF (password: reticulumhf)
4. Open http://192.168.4.1 in browser
5. Complete 6-step setup wizard
6. Connect Sideband to 192.168.4.1:4242

Setup Wizard (6 Steps)

1. Select Radio - Choose from supported radios (tested radios marked)
2. Radio Settings - Configure your radio with the displayed menu values
3. Hardware Detection - Automatically detects Digirig, serial port, audio device
4. Test Connection - Verify CAT and PTT (or check "Using VOX mode" for audio-only)
5. Network Security - Optional IFAC encryption for the gateway
6. Start Gateway - Launches services and redirects to status page

Status Page Features

• Live RX Level - Real-time audio level from modem (updates every second)
  • Target: -15 to -3 dB for good signal
  • Below -35 dB indicates quiet/no signal
• TX Volume Control - Adjustable output volume (-20 to 0 dB)
  • Reduce if radio ALC meter is high or power fluctuates
• Instant Mode Changes - Switch FreeDV modes without service restart
• FreeDV Mode Selection - DATAC1 (fast), DATAC3 (balanced), DATAC4 (robust)
• Service Controls - Restart/view logs for rnsd, rigctld, freedvtnc2
• Troubleshooting Guide - Level adjustment tips and common fixes

FreeDV Modes

Mode	Bitrate	Min SNR	Use Case
DATAC1	290 bps	5 dB	Default - good conditions
DATAC3	124 bps	0 dB	Moderate conditions
DATAC4	87 bps	-4 dB	Poor conditions, weak signals

IMPORTANT: All stations must use the same FreeDV mode to communicate. Coordinate with other operators before changing modes.

Network Configuration

Setting	Value
WiFi SSID	ReticulumHF
WiFi Password	reticulumhf
Gateway IP	192.168.4.1
Web Portal	http://192.168.4.1
RNS Gateway Port	4242 (all clients)
SSH	pi / reticulumhf

Client Connections

All clients connect using TCP Client Interface on port 4242.

Sideband / Columba: Settings → Connectivity → Add Interface → TCP Client

Setting	Value
Interface Type	TCP Client Interface
Address	192.168.4.1
Port	4242

MeshChat: Settings → Interfaces → Add → TCP Client Interface

Setting	Value
Interface Type	TCP Client Interface
Target Host	192.168.4.1
Target Port	4242

Note: If IFAC is configured on the gateway, clients must use matching IFAC Name and Passphrase.

What's Included

• Raspberry Pi OS Bookworm Lite (64-bit)
• RNS (Reticulum Network Stack)
• freedvtnc2 (FreeDV modem)
• codec2 (built from source)
• Hamlib rigctld (CAT/PTT control)
• Web portal with setup wizard and status dashboard

---

Verified Hardware

Component	Model	Notes
Computer	Raspberry Pi 4 (4GB)	Recommended
Radio	Xiegu G90	TESTED - Hamlib 3088, PTT via RTS
Radio	Yaesu FT-818	TESTED - Hamlib 1020 (FT-817), PTT via RTS
Radio	(tr)uSDX	TESTED - VOX mode, Digirig Lite
Interface	Digirig Mobile	CAT + Audio (recommended)
Interface	Digirig Lite	Audio only - use VOX mode
Phone App	Sideband (Android/iOS)	Port 4242
Desktop App	MeshChat	Port 8001, KISS framing

Radio-Specific Notes

Xiegu G90:

• Mode: USB-D (USB Digital)
• AGC: OFF
• AUX IN: 10, AUX OUT: 13
• Hamlib model: 3088, Baud: 19200

Yaesu FT-818:

• Mode: USB or DIG
• Use Hamlib model 1020 (FT-817), NOT 1041
• Baud: 4800
• Set appropriate menu items for DATA input

(tr)uSDX:

• Mode: USB
• Enable VOX (Menu 3.1: ON)
• Adjust Noise Gate (Menu 3.2) for reliable PTT
• Volume (Menu 1.1): 8-10
• TX Drive (Menu 3.3): 4
• Requires Digirig Lite or similar audio interface

---

Manual Installation

For building from scratch on existing Raspberry Pi OS.

Prerequisites

sudo apt update && sudo apt upgrade -y
sudo apt install -y git build-essential cmake python3 python3-pip python3-venv \
    portaudio19-dev alsa-utils libhamlib-utils libhamlib-dev pipx
pipx ensurepath
source ~/.bashrc

Build Codec2

cd ~
git clone https://github.com/drowe67/codec2.git
cd codec2 && mkdir build_linux && cd build_linux
cmake .. && make && sudo make install && sudo ldconfig

Install Reticulum Stack

pipx install rns
pipx install nomadnet
pipx install freedvtnc2
pipx runpip rns install numpy pyaudio scipy

Configure Reticulum

Edit ~/.reticulum/config:

[reticulum]
  enable_transport = no

[interfaces]
  [[Default Interface]]
    type = AutoInterface
    enabled = yes

  [[FreeDV HF]]
    type = TCPClientInterface
    enabled = yes
    target_host = 127.0.0.1
    target_port = 8001
    kiss_framing = yes

Start Services

# Start rigctld (for CAT-controlled PTT)
rigctld -m 3088 -r /dev/ttyUSB0 -s 19200 -t 4532 -P RTS &

# Start freedvtnc2
freedvtnc2 --input-device 1 --output-device 1 --mode DATAC1 \
    --rigctld-port 4532 --kiss-tcp-port 8001 --kiss-tcp-address 0.0.0.0 \
    --ptt-on-delay-ms 300 --ptt-off-delay-ms 200 --output-volume 0

# For VOX mode (no CAT), use --rigctld-port 0
# Reduce --output-volume to -6 or lower if radio ALC activates (power fluctuates)

---

Troubleshooting

Hardware Check

lsusb                      # List USB devices
arecord -l                 # List audio devices
ls -la /dev/ttyUSB*        # List serial ports

CAT/PTT Test

rigctl -m 3088 -r /dev/ttyUSB0 -s 19200 f    # Get frequency
rigctl -m 3088 -r /dev/ttyUSB0 -s 19200 T 1  # Key transmitter
rigctl -m 3088 -r /dev/ttyUSB0 -s 19200 T 0  # Unkey

Common Issues

Radio power fluctuates during TX (4-10W instead of steady 10W):

• ALC is activating due to TX audio being too hot
• Reduce TX Audio Level on status page (try -8 to -12 dB)

Audio in use by modem:

• Status page shows "Audio in use by modem" - click to temporarily stop modem for level check
• Modem automatically restarts after 5 seconds

No serial port detected:

• Check USB cable connection
• Verify Digirig LED is lit
• Run dmesg | tail after plugging in

Radio not keying:

• Verify rigctld is running: systemctl status rigctld
• Test PTT manually: rigctl -m 3088 -r /dev/ttyUSB0 -s 19200 T 1
• For VOX: check radio VOX settings and audio levels

Can't connect from phone:

• Verify connected to ReticulumHF WiFi
• Check interface settings match (TCP Client, 192.168.4.1:4242)
• Verify IFAC settings match if configured

Can't decode signals:

• Verify both stations using same FreeDV mode
• Check audio levels: target -10 to -5 dB on signals
• Try DATAC4 for weak signal conditions

---

Architecture

┌─────────────────────────────────────────────────────────────────┐
│  Client (Sideband/MeshChat/NomadNet)                            │
│  TCP Client Interface → 192.168.4.1:4242                        │
└─────────────────────────────┬───────────────────────────────────┘
                              │ WiFi (TCP:4242)
                              ▼
┌─────────────────────────────────────────────────────────────────┐
│  Raspberry Pi (ReticulumHF Gateway)                             │
│  ┌─────────────┐  ┌─────────────┐  ┌─────────────┐              │
│  │    rnsd     │──│ freedvtnc2  │──│  rigctld    │              │
│  │  (TCP:4242) │  │  (TCP:8001) │  │  (TCP:4532) │              │
│  │  boundary   │  │  FreeDV     │  │  CAT/PTT    │              │
│  └─────────────┘  └─────────────┘  └─────────────┘              │
└─────────────────────────────┬───────────────────────────────────┘
                              │ USB (Audio + CAT)
                              ▼
┌─────────────────────────────────────────────────────────────────┐
│  Digirig Mobile/Lite                                            │
└─────────────────────────────┬───────────────────────────────────┘
                              │ Audio + PTT
                              ▼
┌─────────────────────────────────────────────────────────────────┐
│  HF Radio (G90 / FT-818 / truSDX)                               │
└─────────────────────────────────────────────────────────────────┘

---

References

• Reticulum Manual
• codec2 Data Modes
• freedvtnc2
• Sideband
• MeshChat
• Hamlib Supported Radios

License

MIT License - See LICENSE file

Author

Light Fighter Manifesto L.L.C. https://lightfightermanifesto.org