ESP_ERR_HTTPD_RESP_SEND on ESPS3 REV1:1

[viktorp75]

I have 1 issue and 1 question.

Question is whether REV1:1 is the same as REV1:0? In terms of slow PSRAM 8GB from which can only 4GB be used.

The issue is that I cannot make the device working with this project. I was able to install the CameraWebServer example.

Getting this in log:

`00:00:00.911 logSetup] Setup RAM based log, size 7168, starting from 0

[00:00:00.912 logSetup] =============== ESP-CAM_MJPEG 10.6.2 ===============
[00:00:00.914 boardInfo] Chip ESP32-S3, 2 cores @ 240Mhz, rev 0
[00:00:00.914 boardInfo] Flash 16.0MB, mode QIO @ 80Mhz
[00:00:00.914 boardInfo] PSRAM 8.0MB, mode QSPI @ 80Mhz
[00:00:00.915 logSetup] Compiled with arduino-esp32 v3.2.1
[00:00:00.915 printResetReason] Power on reset
[00:00:00.915 printWakeupReason] Wakeup by reset
[00:00:00.915 setup] Selected board CAMERA_MODEL_NEW_ESPS3_RE1_0
[00:00:03.274 infoSD] SD card type SDHC, Size: 29.1GB, using 1 bit mode @ 40MHz
[00:00:03.274 listFolder] Sketch size 1.5MB
[00:00:08.058 listFolder] File: /data/configs.txt, size: 7847 bytes
[00:00:09.239 listFolder] File: /data/common.js, size: 48985 bytes
[00:00:10.435 listFolder] File: /data/MJPEG2SD.htm, size: 97KB
[00:00:10.435 listFolder] SD_MMC: 16.5GB used of 29.1GB
[00:00:10.435 loadConfig] Load config
[00:00:23.912 updateAppStatus] Enabling motion detection
[00:00:23.916 prepCam] Max frame size for 8.0MB PSRAM is QSXGA
[00:00:24.205 prepCam] Camera model OV2640 ready @ 20MHz
[00:00:24.370 setWifiSTA] Wifi Station IP from DHCP
[00:00:24.389 WARN startWifi] SSID not connected not available, use AP
[00:00:24.390 onWiFiEvent] Wifi AP SSID: ESP-CAM_MJPEG_0C8C004AEC24 started, use 'http://192.168.4.1/' to connect
[00:00:24.392 setupMdnsHost] mDNS service: http://esp-cam_mjpeg_0.local/
[00:00:27.407 startPing] Started ping monitoring - On
[00:00:27.409 startWebServer] Starting web server on port: 80
[00:00:27.409 startWebServer] Remote server certificates not checked
[00:00:27.410 startSustainTasks] Started 1 sustain tasks
[00:00:27.428 updateAppStatus] Enabling motion detection
[00:00:27.528 prepRecording] To record new AVI, do one of:
[00:00:27.528 prepRecording] - press Start Recording on web page
[00:00:27.528 prepRecording] - move in front of camera

[00:00:27.528 checkMemory] Setup Free: heap 152756, block: 90100, min: 152756, pSRAM 5666012
[00:00:27.529 loop] =============== Total tasks: 18 ===============

[00:00:29.777 isNight] Night time
[00:00:32.407 resetWatchDog] WatchDog started using task: ping
[00:00:44.642 onWiFiEvent] WiFi AP client connection
[00:00:51.551 WARN sendChunks] Failed to send to browser: /data/MJPEG2SD.htm, err ESP_ERR_HTTPD_RESP_SEND`

I tried to connect to a stronger 5V source. Not sure what else to try. Any idea?

[s60sc]

[00:00:00.915 setup] Selected board CAMERA_MODEL_NEW_ESPS3_RE1_0

As stated in readme:

avoid no-name boards marked ESPS3 RE:1.

as they have problems, so

[00:00:51.551 WARN sendChunks] Failed to send to browser: /data/MJPEG2SD.htm, err ESP_ERR_HTTPD_RESP_SEND

is due to deficient wifi connection, use browser inspector or wireshark to investigate

[viktorp75]

I had this board in my drawer for a year and read this warning only yesterday, so too late.
But I resolved it in the end and made the ESPS3 RE:1 working. The problem was that I used a memory card from another already working board Freenova S3 where the files are obviously different? Using a new SD card resolved the problem.
Thanks